NOTE: This is a very important step as the bobbin can become unthreaded and cause sewing problems if it rotates clockwise. This is especially important if you are running out of bobbin thread in the middle of topstitching or when you are sewing leather. Wind the thread through all the threading points--the thread guide on the top of the sewing machine, the tension discs and the takeup lever. It’s a two-part process in which you’ll learn how to wind the bobbin and then thread the machine. The lower thread comes from the bobbin, a small spool of thread that’s loaded under the slide plate of the machine. One that many beginners struggle with is putting thread on the bobbin, which is often referred to as bobbin threading or bobbin winding. Even with its simplistic design, often getting started takes a bit of time, concentration and practice. Push bobbin winder shaft to the right until it clicks. Then look for another thread guide that is out of place, down lower or off to another side, and wrap your thread … This thread connects with the thread on your needle and forms stitches. Re-adjust it and tug the bobbin thread gently.

10. And you’re done! Leave a tail of thread about 6 inches long to use for attaching to the bobbin. Place a spool of thread on the horizontal spool holder on top of the Singer 756. Knowing how to correctly thread your sewing machine opens up a world of creative possibilities. You should try tugging on the threads when you start sewing, both the upper and bobbin threads. Check to see whether the bobbin is placed correctly in the bobbin case. Push bobbin winder shaft to far left position, if it is not already there. 4. Insert the bobbin making sure the bobbin rotates counterclockwise when you pull the thread. You can cut the stray thread at the top of the bobbin once the bobbin is partially wound, or you can wait until the process is complete to cut it. Now that your bobbin is wound, get it inserted into the Singer sewing machine and it's ready to start sewing. 3. Place bobbin onto shaft with end of thread coming from top of bobbin. Holding thread end, step on speed controller to run the machine until the desired amount of thread is wound. Start the bobbin winder. The bobbin is a small spool of thread that is loaded underneath your needle and it supplies the thread that comes up through the base of your machine. Watch this video sewing tutorial and learn how to insert the bobbin into a Singer … For mine I have to make sure my bobbin is threading out counter clockwise. Bobbin cover will pop up sufficiently to allow you to remove the cover. The SINGER START sewing machine gives beginning sewists and hobbyists just enough features to get their creativity off the ground. Perfect for beginners and hobbyists. But don't panic––this problem is almost always easy to fix. The Singer Touch & Sew machine from the 1970s is an amazingly versatile machine still appreciated by Singer enthusiasts.

I start by plasing the bobbin in its casing. I’ve written about my Singer 66 before, but I wanted to share some videos I prepared about this fantastic, reliable vintage sewing machine. This video shows how to thread your bobbin on a side threading sewing machine. Many of the features were state-of-the art at the time of their introduction. Trim thread ends from top of the bobbin. Make sure to watch the thread as it winds, to make sure it winds evenly and does not end up going off of your bobbin. Cut thread; push bobbin to the left and remove it from bobbin winder pin (illustration 4).

Replacing the bobbin case after changing the thread spool gets you back to sewing. The Singer Simple model is designed for the beginning sewer. For example, the 700 series featured automatic needle threading and the "wind in place" bobbin. Start winding the bobbin for a few seconds by pushing down on the foot pedal or by pressing the bobbin winding button (if your machine has one).

2. 8. To wind the bobbin, insert the thread through the hole in your spool and then wind it around the bobbin a couple of times. A singer sewing machine sews with two threads: an upper and lower thread. Hold the end of thread. The thread on a bobbin should not exceed the size of the bobbin. (Winding stops automatically once bobbin is full.) To wind your bobbin, start by placing your spool of thread on the machine, and threading the (first) top thread guide, as you would if you were threading the machine.

Put end of thread through the hole in bobbin as shown. We start off by making sure that the needle is in the most upright position. The thread on a bobbin should be as smoothly wound as the thread on a purchased spool of thread. Start every project with a full bobbin and fill a few bobbins for the project at once so when your bobbin thread runs out you have another one ready. The upper thread comes from the spool and is threaded through the eye of the needle of the sewing machine. Without the bobbin casing properly in … Singer 1304 Start Sewing Machine.